spsemi rev 2017 01 06 ... www.spsemi.cn page 1 of 4 s urface mount t r ansie nt v oltag e suppressor stand-off voltage - 6.0 to 170 v o lts 1000 w att peak pul s e power features for surface mounted applications in order to optimize board space low profile package built-in strain relief glass passivated junction low inductance excellent clamping capability repetition rate (duty cycle):0.05% fast response time: typically less than 1.0ps from 0 volts to v(br) for unidirectional types typical ir less than 1a above 10v high temperature solderting: 260c/10 seconds at terminals plastic package has underwriters laboratory flammability 94v-o pb-free plated tecc(1000w) series mechanical data devices for bipolar application for bidirectional use c or ca suffix for types tecc6.0 thru types tecc440 (e.g. tecc6.0c , tecc440ca) electrical characteristics apply in both directions maximum ratings and characteristics ratings at 25 ambient temperature unless otherwise specified. notes : 1.non-repetitive current pulse , per fig. 3 and derated above ta = 25 per fig. 2 . 2.mounted on 8.0mm x 8.0mm copper pads to each terminal 3.8.3ms single half sine-wave , or equivalent square wave, duty cycle = 4 pulses per minutes maximum. peak pulse power dissipation on 10/1000s waveform (note 1,2 ,fig.1) peak pulse current of on 10/1000s waveform (note 1,fig.3) peak forward surge current,8.3ms single half sine-wave superimposed on rated load,(jedec method) (note2,3) operating junction and storage temperature range rating symbol value units p ppm i ppm i fsm t,t jstg minimum 1000 see table 1 - 55 to +150 200 watts amps amps case: jedec do-214aa. molded plastic over glass passivated junction terminals: solderable per mil-std-750,method 2026 polarity: color band denoted positive end (cathode) except bidirectional 12mm tape (eia std rs-481) standard packaging: 0.003ounce,0.093gram weight:
spsemi www.spsemi.cn page 2 of 4 dimensions (do-214aa) electrical characteristics tecc6.0a tecc8.0a tecc12a tecc15a tecc16a tecc20a tecc22a tecc26a tecc28a tecc30a tecc33a TECC36A tecc40a tecc58a tecc60a tecc150a tecc170a tecc part number device marking code reverse stand-off voltage v (v) rwm v (v)min. br v (v)max. br te s t current it(ma) maximum clamping voltage @ipp vc(v) peak pulse current ipp(a) reverse leakage @v rwm i(a) r
spsemi www.spsemi.cn page 3 of 4 characteristic curves (ta=25 unless otherwise noted) fig.1 peak pulse power rating fig.2 pulse derating cruve fig.3 pulse waveform fig.4 typical junction capacitance 0 0 1.0 2.0 4.0 3.0 10/1000 sec waveform . s.. ss s s s s . s s s . ss. . s s . s s s . s s . s s s . . . . s . .s . . . . . s ss . s .ss . s ...
spsemi www.spsemi.cn page 4 of 4 marking code tape and reel specification recommended soldering conditions recommended conditions reflow soldering t s t p t l time 25 time to peak temperature (t 25 to peak) temperature t (min) s t (max) s t l t p preheat ramp-down ramp-up critical zone ttot lp re?ow condition pb-free assembly (see fig.1) pre heat -temperature min(t ) s(min) -temperature max(t ) s(max) -time(min to max)(t ) s average ramp up rate (liquidus temp(t ) to peak) l t to t -ramp-up rate s(max) l re?ow -temperature(t )(liquidus) l -temperature(t ) l peak temp(t ) p time within 5 of actual peak temp(t ) p ramp-down rate time 25 to peak temp(t ) p do not exceed +150 +200 60-180secs 3 /sec.max. 3 /sec.max. +217 60-150secs +260(+0/-5) 30 secs.max. 6 /sec.max. 8 min.max. +260 cathode band 6 d **** marking code logo date code 6 h **** marking code logo date code tecc(1000w) series 0.157 (4.0) 0.47 (12.0) 0.314 (8.0) 0.49 (12.0) symbol ea per reel reel dia (mm) industry standard tecc*** 3000 330 eia rs-481 13.0(330) rev 2017 01 06 ...
|
